Description

NPK C-2D PLATE COMPACTOR- IMPULSE FORCE: 3500 LBF- CYCLES PER MINUTE: 2400- OIL FLOW: 13 GPM- OPERATING PRESSURE: 1500-2000 PSI- RELEIF PRESSURE SETTING: 2500 PSI- BASE PLATE DIMENSIONS: 12 X 25"- COMPACTION AREA: 2.1 SQ FT- WEIGHT: 390 LBS- HEIGHT: 28"- WIDTH: 12

Description

DYNAPAC CA2500D SOIL COMPACTORSTANDARD OPTIONS:- BACK UP ALARM- ELECTRONIC THROTTLE- HYDRAULIC PRESSURE CHECKPOINTS- BRAKE RELEASE- PARKING BRAKE- LOCKABLE HOOD- ENGINE: CUMMINS QSB 3.8 T4F 120 HP- RUBBER MOUNTED OPERATION PLATFORM- DRUM: 84"X59"- SEAT BELT- EMERGENCY STOP- CANOPY- TIRES: 23.1-26 AW 8 PLY- FREQUENCY: 2040 BPM- WARNING LAMPS- FUEL GUAGE- HORN- HOUR METER- SWIVEL SEAT- FUEL TANK CAPACITY: 72 GALLONS- LED WORKLIGHT WITH BEACON- TRACTION CONTROL- MIRRORS- DRUM SCRAPER- SEISMIC PAACKAGE: SEISMIC CONTROLACTIVE BOUNCING CONTROLDYNAPAC COMPACTIONMETER

Description

FINLAY I-120RS EQUIPPED AS PER BELOW:ENGINE- TIER 4 FINAL /STAGE IV : SCANIA DC9 257KW (350 HP) ENGINEIMPACT- TEREX CR038 IMPACT CHAMBERCHAMBER:- FULLY HYDRAULICALLY ASSISTED APRON SETTING AND HYDRAULIC APRON RELEASE- MANUAL RAISE CHAMBER FLAP ALLOWING EXTRA INLET CLEARANCE- 4 BAR ROTOR - MARTENSITIC BLOW BARS 2 HIGH & 2 LOW- DIRECT DRIVE VIA CLUTCH- DRIVE BELT TENSIONER WHEEL- BLOW BAR LIFTING TOOL SUPPLIED.- SMALLER ENGINE CHAMBER DRIVE PULLEYTO GIVE A ROTOR LOWER SPEED RANGE.STANDARD LARGE PULLEY STILL DISPATCHED WITH MACHINE- ROTOR FITTED WITH 2 FULL MARTENSITIC CERAMIC & 2 LOW MARTENSITICBLOW BARSHOPPER & FEEDER:- VGF FIXED HOPPER- STEPPED GRIZZLY FEEDER WITH INTEGRAL PRE-SCREENSTANDARD 50MM SPACING- MESH APERTURE ON GRIZZLY FEEDER: 38MM- SELECTABLE DISCHARGE TO BY-PASS CONVEYOR OR MAIN CONVEYOR- BLANKING MAT FOR VGF- INDEPENDENT PRE-SCREEN C/W HYDRAULICALLY FOLDING AND LOCKINGHOPPER AND BLANKING MAT. 2" SQUARE OPENING SCREENS INSTALLEDBLANKING MATINSTALLED- INDEPENDENT PRE-SCREEN HOPPER EXTENSIONS- BOFOR BARS REMOVED IN THE INDEPENDENT PRE-SCREENMAIN CONVEYOR:- 1100MM (43.3") BELT FULL LENGTH- UNDER CRUSHER VIBRATORY FEEDER WITH WEAR RESISTANT STEEL LINERS (C/W SHORTENEDMAIN CONVEYOR)AUXILIARY CONVEYORS:- HYDRAULIC RAISE/ LOWER FOR MAGNET- PIPED FOR OVER BAND MAGNET- BYPASS CONVEYOR WITH 650MM WIDE PLAIN BELTDISCHARGING TO THE LHS OF THEMACHINE.- TWIN POLE OVER BAND MAGNET C/W STAINLESS STEEL SKIRTING & STAINLESS STEELDISCHARGE CHUTEDISCHARGING TO RHS OF THE MACHINE.RS COMPONENTS:- 3.66M X 1.52M (12- X 5-) TWO DECK AFTER SCREEN C/W 50MM TOP DECK AND 40MMBOTTOM DECK MESH AS STANDARD UNLESS OTHERWISE STATED- 500MM (20") WIDE BELT SINGLE TRANSFER CONVEYOR COLLECTING MATERIAL FROM BOTHDECKS.- 500MM (20") WIDE BELT HYDRAULIC FOLDING RE-CIRCULATING CONVEYOR ABLE TO SLEWFOR STOCKPILING OVERSIZE MATERIAL- 1400MM (55") WIDE BELT FINES CONVEYOR- RAPID DETACH AFTER SCREEN SYSTEM FOR FLEXIBILITY.- BELT WEIGHER- ADDITIONAL TRANSFER CONVEYOR FOR COLLECTING MATERIAL FROM EACH INDIVIDUAL DECKOF SCREEN BOXCLIMATE SPEC:- STANDARD OILS - (RECOMMENDED FOR AMBIENT TEMPERATURES BETWEEN -5 TO +30C)DUST SUPPRESSION:- PIPED FOR DUST SUPPRESSION C/W SPRAY BARS- WATER PUMP FOR DUST SUPPRESSIONELECTRICAL:- EMERGENCY STOPS- HAND HELD TRACK CONTROL SET WITH CONNECTION LEAD- T-LINK TELEMETRY SYSTEM FITTED C/W 3 YEARS DATA SUBSCRIPTION- RADIO REMOTE SYSTEM: OPERATIONAL CONTROLS OF MACHINE (AUTO START/STOP) & TRACKMOVEMENT- PRESSURIZED AIR SYSTEM FOR ELECTRICAL CONTROL CABINET- LIGHTNING MASTSAFETY GUARDS IN COMPLIANCE WITH MACHINERY DIRECTIVE

Description

HENSLEY SK500 54" GENERAL PURPOSE BUCKET- KMAX TEETH - STRIKEOFF SIDECUTTERS

Description

- 15MNHD24-S- 24" HEAVY DUTY BUCKET- BOE- INCLUDES PINS- FIT SK55/SK45

Description

KOBELCO SK30SR-6E- CANOPY MACHINE - RUBBER TRACKS - STANDARD BOOM - AUXILLARY HYDRAULICS - STANDARD 4-4" ARM WITH THUMB BRACKET

Description

- EKKC-70/90-01.98-54-BASE- KRYPTO KLAW STANDARD-DUTY BUCKET- 54" WIDE- 1.98 YD BUCKET CAPACITY- 81" MAXIMUM THROAT OPENING- WITH 6 TEETH INSTALLED- HENSLEY KMAXK40SHARPRIBBED POINTS- K120040 ADAPTERSK40SYL POINTSKP40C PINS- BUCKET PINSONE SET.- NOT TO BE USED IN PLACE OF OEM BUCKET PINS.- BOLT-ON CYLINDER GUARDS- 6032 LBS- TO FIT A KOBELCO SK350LC-9/10 WITH COUPLER

Description

KOBELCO SK300LC-10 HYDRAULIC EXCAVATORENGINE: - HINO JO8EV-KSDP 6 CYL TIER 4B - 252 HP (188 KW) / 2 100 RPM (SAE NET) - 729 LB-FT / 1 600 RPM (SAE NET)GENERAL: - ENERGY SAVING SYSTEM WITH ECO MODE AND AUTO HYDRAULIC WARM UP - MACHINE OPERATION MANAGEMENT SYSTEM WITH GPS - ROPS/FOPS SOUND SUPPRESSED CAB WITH SILICON VISCOUS MOUNTS - HAND CONTROL PATTERN CHANGER - TWO WAY ISO/BHL- BELLY PAN - ANGLE GUARDS - REARVIEW CAMERAAND MIRRORS - AIR CONDITIONED CAB - LONG UNDERCARRIAGE - TINTED GLASS WITH TOP GUARD

Description

WERK BRAU SK25 24" GENERAL PURPOSE BUCKET- WITH PINS

Description

WERK BRAU SK25 12" GENERAL PURPOSE BUCKET- WITH PINS

Description

- EX20HD42- PIN-ON STYLE- 1.22 CU/YRD- 5 - KMAX K20 STANDARD TEETH- 2050LBS- INCLUDES PINS

Description

CANICA CRV2000 5 SHOE TABLE IMPACTOR CRUSHING PLANT EQUIPPED AS PER BELOW:- TEREX CANICA 2000 VERTICAL SHAFT IMPACTOR WITH AUXILIARYELECTRICAL CONTROL CABINET WITH RPM GUAGEVIBRATION DETECTOR(WARNING) LIGHTHOUR METEROPEN-LID CRUSHER SAFETY CUT-OFF2 HPLUBE SYSTEM STARTEROIL SYSTEM HEATER STARTER AND 15 HP SPARESTARTER. CONTAINS TERMINATION POINTS FOR ALL SAFETY SHUT-OFFSWITCHES.- PANTENTED "HYDRALID" HYDRAULIC LID LIFTER & MODULAR OIL LUBESYSTEM- 48" (1219MM) WIDECOVERED PRODUCT CONVEYOR AND HOODWITH 15 HP (11KW) ELECTRIC MOTOR - SUPERSCREW BELT SPLICE- EXTERNALLY ADJUSTABLE FEED TUBE SYSTEMFEED HOPPER WITH BANGBOARD- SERVICE PLATFORMS AROUND CRUSHER WITH INCLINED ACCESS LADDER TOGROUND- EASY MAINTENANCE FEATURES; REMOTE GREASE LINESGROUND ACCESSCONE LUBRICATION MODULE- EMERGENCY STOP BUTTONS ON BOTH SIDES OF THE FRAME- TANDEM AXLE SPRING SUSPENSION WITH EIGHT (8) 295/75 R22.5 TIRES- 48" (1219MM) LONG LOCKABLE SIDE-MOUNTED STORAGE BOX- 2000 HEAVY DUTY SAND (HDS) VSI SINGLE DRIVE WITH OPEN TABLE ANDANVILS - UP TO 250 STPH FEED RATE AND UP TO 2" (25MM) FEED SIZE- 460 VOLT3 PHASE60 HERTZ- 300 HP 1200 RPM 460/60 HERTZ SINGLE DRIVE ELECTRIC MOTOR- SET OF FOUR (4) 6" X 24" STROKE DUAL PINNED HYDRAULIC RUN-ON JACKSAND GAS POWER- PAINTED GRAPHITE GRAY (RAL 7024) WITH SAFETY YELLOW HANDRAILSLADDERS AND GUARDING- AES ELECTRICAL SWITCHGEAR PANEL EQUIPPED AS PER BELOW:- 60X60 NEMA 3R/4 ENCLOSURE- DRIP SHIELDCORD CAGE- MANUALLY OPERATED SAFETY START UP ALARM- 800 AMP MAIN CIRCUIT BREAKER WITH LOCKABLE OPERATOR - ADJUSTED TO700 AMPS- IMPACTOR AMP METER AND HOUR METER- PLANT HZ METER- PLANT VOLT METER- ACS880 ABB BRAND VFD- POTENTIOMETER FOR SPEED CONTROL- 900 CFM HEAT EXCHANGER ON A SWITCH- CONTROL BUTTONS IN THE DOOR- 25 HP FEED CONVEYORNEMA/IEC RATEDSIZE 2 STARTER - 60 AMPRECEPTACLE AND PLUG - INTERLOCKED- 20 HP SPARE 1 CONVEYOR - SIZE 2 STARTER - 60 AMP RECEPTACLE AND PLUG- 20 HP SPARE 2 CONVEYOR - SIZE 2 STARTER - 60 AMP RECEPTACLE AND PLUG- 20 HP SPARE 3 CONVEYOR - SIZE2 STARTER - 60 AMP RECEPTACLE AND PLUG- 5 KVA TRANSFORMER WITH (1) 120 VAC20 AMP GFCI DUPLEX -WEATHERPROOF- 60 AMP FEED BREAKER FOR CANICA POWER PANEL- VIBRATION SWITCH AND WIRING- VIBRATION INDICATOR LIGHT- HOUR METER- RPM GUAGE- LUBE STARTER AND CONTROLS- UNDER CRUSHER STARTER AND CONTROLS- 100- OF POWER CORD CONSISTING OF (2) PARALLEL RUNS OF 4/0 TYPE W PERPHASEQTY. (1) 4/0 TYPE W GROUND- SG PANEL SETS OFF THE GROUND 30- FOR OPERATION- GUARDING - WE DO NOT WARRANT THAT OUR GUARDS WILL MEET ALLLOCAL CODES.IT IS THE RESPONSIBILITY OF THE END USER TO HAVE THEMCHECKED BY A LOCAL INSPECTORS/N# OF CANICA CRUSHER 2000188-19

Description

KOMATSU HM300-5 ARTICULATED DUMP TRUCK EQUIPPED WITH:ENGINE:- KOMATSU SAA6D125E-711.0 L DISPLACEMENT DIRECT INJECTION SYSTEMKOMATSUVARIABLE GEOMENTRY TURBOCHARGERAFTERCOOLEDEPA TIER 4 FINAL EMISSIONCERTIFIED DIESEL ENGINE- GROSS HP: 333 HP (248 KW) / 2000 RPM- FLYWHEEL HP: 325 HP (242 KW) / 2000 RPM- FULL-AUTOMATIC F6 R2 TRANSMISSION WITH K-ATOMIC SHIFT CONTROL WITH AUTOMATICT/C LOCK-UP- ALTERNATOR90AMP24 VOLT- BATTERIES 2X12 VOLT200 AH- KDPF - AFTER-TREATMENT ASSEMBLY CONSISTING OF KDOC AND KCSF- SELECTIVE CATALYTIC REDUCTION (SCR) SYSTEM- TWO MODE ENGINE POWER SYSTEM (ECONOMY AND POWER MODES)OPERATOR EQUIPMENT- ROPS CAB W/FOPSLEVEL 2- AIR CONDITIONER/HEATER/DEFROSTERELECTRONICALLY CONTROLLED- ELECTRONIC HOIST CONTROL SYSTEM- RADIO AM/FMWITH AUXILLIARY JACK- REAR WINDOW GUARD- SEATAIR SUSPENSIONRECLINING (FABRIC)- TILT AND TELESCOPIC STEERING WHEEL- TILTCAB ARRANGEMENT FOR EASY SERVICELIGHTING SYSTEM:- BACK-UP LIGHT- HAZARD LIGHT SYSTEM- HEADLIGHTSFRONT- STOPTAIL AND TURN SIGNAL LIGHTSLED TYPE- WORKING LIGHTSFRONT AND LEFT/RIGHT SIDEPILOT LIGHT:- ENGINE PREHEAT- MONITORING SYSTEMLCD DISPLAYOTHER STANDARD EQUIPMENT:- AUXILIARY STEERING SYSTEMAUTOMATICELECTRIC- CENTRALIZED GREASING- HYDROPNEUMATIC SUSPENSIONFRONT AND REAR- INTERAXLE LOCKUPWET DISC CLUTCH TYPECONTROLLED BY K-TCS- KOMATSU TRACTION CONTROL SYSTEM (KTCS)- KOMTRAX LEVEL 4- PAY LOAD METER 2.5- PROVISION FOR TAILGATE INSTALLATION- REARVIEW CAMERA W/ SEPARATE IN CABIN MONITORINCLUDED OPTIONAL EQUIPMENT:- 23.5R25 VLT E3 BRIDGSTONE TIRES- BODY WITH EXHAUST HEATING DUCTING22.4 CUBIC YARDS- EXHAUST PIPING KDPF TO BODY- TAILGATESCISSORS TYPE

Description

- EX20HD48- PIN-ON STYLE- 1.41 CU/YRD- 6 - KMAX K20 STANDARD TEETH- 2275LBS- INCLUDES PINS

Description

NPK C-2D TOP PLATE- TO FIT KOBELCO SK35

Description

KAWASAKI 70Z7 WHEEL LOADER EQUIPPED WITH:- CUMMINS QSB6.7 DIESEL ENGINE- LIMITED SLIP DIFFERENTIAL- LOAD SENSING TRANSMISSION- AUTOMATIC REVERSING FAN- COLD START INTAKE HEATER- DUAL ELEMENT AIR CLEANER- AUTO IDLE SHUT DOWN- BOOM KICKOUT AND BUCKET POSITIONER- BACK UP CAMERA- FIRE EXTINGUISHER- HEATED SEAT WITH TLV SUSPENSION- RIDE CONTROL KIT- 120V BLOCK HEATER- COUNTERWEIGHT- QUICK COUPLER 416 SERIES- RADIAL 20.5 R25 L3 TIRES

Description

KOBELCO SK210LC-10ENGINE:- HINO JO5E-UM 4 CYL TIER 4 FINAL- 160 HP (119 KW) / 2 000 RPM (SAE NET)- 472 LB-FT / 1 600 RPM (SAE NET)GENERAL:- ENERGY SAVING SYSTEM WITH ECO MODE AND AUTO HYDRAULIC WARM UP- MACHINE OPERATIONMANAGEMENT SYSTEM WITH GPS- ROPS/FOPS SOUND SUPPRESSED CAB WITH SILICON VISCOUS MOUNTS- HAND CONTROL PATTERN CHANGER- ANGLE GUARDS- REARVIEW CAMERAAND MIRRORS- AIR SUSPENSION SEAT- SEMI-TRIPLE GROUSER SHOES 31.5" (800MM)- HDBOOM18-6"- HD ARM9-9

Description

WERK BRAU SK35 MANUAL PIN-GRABBER QUICK COUPLER- SET OF PINS

Description

KC4700 - SERIES 47 - STACKABLESERIES 47 36" X 60- STACKABLE CONVEYOR WITH COLLAPSIBLE UNDERCARRIAGE- FRAME: 27" HEAVY DUTY LATTICE TYPE FRAME DESIGNED WITH RECESSEDRECEIVING TROUGHTROUGHING AND RETURN IDLERS TO ALLOW FORSTACKING ON ON ANOTHER FOR EASE OF TRANSPORTATION- UNDERCARRIAGE: MANUAL TELESCOPING PIN LOCK; AXLE - SINGLE AXLEWITH SINGLE 11:00X22.5 TIRES ON SWIVEL WHEEL BOXEX - COLLAPSIBLE TYPEUNDERCARRIAGE- HEAD PULLEY: RUBBER LAGGED PULLEY- TAIL PULLEY: WING TYPE SELF CLEANING- DRIVE ASSEMBLY: 20 HP WITH CLASS I GUARDED GEAR REDUCER WITHBACKSTOP BELT SPEED SET FOR 350 FPM MOTOR - ELECTRIC TEFC 3/60/460- RECEIVING TROUGH: 5-6" LONG- IDLERS: CEMA-B5" DIAMETER STEEL- TROUGHING: 3-ROLL20 DEGREE UNDER RECEIVING TROUGH; 35 DEGREETHEREAFTER ON 4- SPACING- RETURN: STEEL ROLL ON 10- SPACING WITH RETURN ROLL GUARDS ASREQUIRED- BELTING: 2 PLY220 PIW 1/8" TOP X 1/16" BOTTOM COVERSMECHANICALFASTENER SPLICE- BELT TAKE UP: SCREW TYPEINCLUDED OPTIONS:- GRADE 23 PLY 330 PIW 3/16" X 1/16" COVERS VS STANDARD- BELT CLEANER - MARTIN PIT VIPER WITH TENSIONER- PINTLE HITCH- UNDERCARRIAGE - MANUAL TELESCOPING PIN LOCK;SINGLE AXLE WITHSINGLE 11:00X22.5 TIRES ON SWIVEL WHEEL BOXEX - COLLAPSIBLE TYPEUNDERCARRIAGE- RADIAL HOPPER - ROCK BOX STYLESTAKE POCKETSREMOVABLE SIDES- VULCANIZED BELT SPLICE- KING PIN- RADIAL TIRES VS STANDARD BIAS- PAINT RAL7024 GRAPHITE GREY WITH YELLOW SAFETY GUARDS ANDRAILINGS- KPI DECALS-CONVEYOR SHIPS FULLY ASSEMBLED ON TRAILER WITH 2 OTHER UNITS- GUARDING - FOR DRIVE AND TAIL PULLEYSV-BELT DRIVEAND RETURNIDLERS. GUARDS MAY NOT MEET ALL LOCAL CODESIT IS THE RESPONSIBILITYOF THE END USER TO HAVE THEM CHECKED BY A LOCAL INSPECTOR- ELECTRICAL SWITCHGEAR WITH 200- OF POWER CORD

Description

- INCLUDES PINS- KMAX TEETH- 42" WIDE- 90MM PINS

Description

- 15MNHD18- 18" HEAVY DUTY BUCKET- 4.50 SU FT / 4-TEETH- INCLUDES PINS- FITS SK55/SK45

Description

DYNAPAC COMPACTOR- OROPS- 66" PADFOOT COMPACTOR- 75 HP KUBOTA DIESEL ENGINE- APPROX. 14 500 LBS.- 542 HRS

Description

FINLAY J-1160 TRACKED JAW CRUSHER EQUIPPED AS PER BELOW:ENGINE:- TIER 4 FINAL CAT 7.1 205KW (275HP)JAW CHAMBER:- TEREX 1000 X 600MM (40" X 24") SINGLE TOGGLE JAW CRUSHER HYDROSTATICALLY DRIVEN- FULLY HYDRAULICALLY ADJUSTABLE CLOSED SIDE SETTING- S TOOTH LINERS - 18% MANGANESE VS STANDARD- HYDRAULIC DEFLECTOR PLATE - FITS UNDERNEATH JAWHOPPER & FEEDER:- GRIZZLY FEEDER WITH INTEGRAL PRE-SCREENSTANDARD 50MM SPACING- SELECTABLE DISCHARGE TO BY-PASS CONVEYOR OR MAIN CONVEYOR- MESH APERTURE ON GRIZZLY FEEDER: 30MM- ADDITIONAL CATWALK AT INLET CHUTE ON RHS OF M/CGIVING ACCESS TO BOTH SIDESOF THE FEEDER- HYDRAULIC FOLDING & LOCKING HOPPER EXTENSIONSMAIN CONVEYOR:- 900MM WIDE MAIN BELT FITTED WITH IMPACT BARS AT FEED POINT- PIPED FOR OVERBAND MAGNET- HYDRAULIC RAISE/LOWER OF MAIN CONVEYOR- RIP STOP BELTAUXILIARY CONVEYORS:- BYPASS CONVEYOR WITH 650MM WIDE PLAIN BELTLEFT HAND SIDE DISCHARGE.- TWIN POLOVER BAND MAGNETRHS DISCHARGE (C/W SKIRTING & CHUTE AS ABOVE)CLIMATE SPEC:- STANDARD OILS - (RECOMMENDED FOR AMBIENT TEMPERATURES BETWEEN -5 TO +30 C)DUST SUPPRESSION:- PIPED FOR DUST SUPPRESSION COMPLETE WITH SPRAY BARS - LESS WATER PUMPELECTRICAL:- EMERGENCY E-STOPS- HANDHELD TRACK CONTROL SET WITH CONNECTION LEAD- T-LINK TELEMTRY SYSTEM C/W 7 YEARS DATA SUBSCRIPTION- RADIO REMOTE SYSTEM: OPERATION CONTROLS OF MACHINE (AUTO START/STOP) & TRACKMOVEMENT- CONTROL PANEL POSITIVE AIR PRESSURIZATION- FEEDER CONTROL STATIONGENERAL:- DUAL SPEED TRACKS- SEPARATE CENTRAL OPERATORS PANEL- GUARDING - WE DO NOT WARRANT THAT OUR GUARDS WILL MEET ALL LOCAL CODES. IT ISTHE RESPONSIBILITY OF THE END USER TO HAVE THEM CHECKED BY A LOCAL INSPECTOR

Description

- SIZE: 6 x 6" (152 MM X 152 MM) FLANGED.- CASING: DUCTILE IRON 65-45-12.- MAXIMUM OPERATING PRESSURE 99 PSI (683 kPa).*- OPEN TYPETWO-VANE IMPELLER: DUCTILE IRON 65-45-12.- HANDELS 3" (76 2 MM) DIAMETER SPHERICAL SOLIDS.- SUCTION COVER: GRAY IRON 30.- IMPELLER SHAFT: STAINLESS STEEL 17-4 PH- REPLACEABLE WEAR PLATE: DUCTILE IRON 30.- REMOVEABLE CLEANOUT COVER PLATE: GRAY IRON 30- INTERMEDIATE BRACKET: GRAY IRON 30.- SEAL PLATE: GRAY IRON 30.- SEAL: MECHANINCAL. OIL-LUBRICATED. SILICON CARBIDE ROTATING ANDSTATIONARY FACES. STAINLESS STEEL 316 STAATIONARY SEAT.FLUOROCARBON ELASTOMERS (DUPONT VITON* OR EQUIVALENT). STAINLESSSTEEL 18-8 CAGE AND SPRING- MAXIMUM TEMPERATURE OF LIQUID PUMPED160*F (71*C).*- SHAFT SLEEVE: STAINLESS STEEL 17-4.- PRIMING CHAMBER: GRAY IRON 30 HOUSING W/STAINLESS STEEL FLOATAND LINKAGE.- DISCHARGE CHECK VALVE: DUCTILE IRON HOUSING W/BUNA-N FLAPPER.- RADIAL/THRUST BEARING:OPEN DOUBLE BALL.- BEARING AND SEAL CAVITY LUBRICATION: SAE 30 NON-DETERGENT OIL.- GASKETS: RESISTANT SYNTHETICS RUBBERCORKPTFEVEGETABLE FIBERAND COMPRESSED SYNTHETIC FIBERS- ORINGS: BUNA-N- HARDWARE: STANDARD PLATED STEEL- BEARING AND SEAL CAVITY OIL LEVEL SIGHT GAUGES.ENGINE SPECIFICATIONS- MODEL: JOHN DEERE 4045T- FOUR CYLINDERFOUR CYCLETURBOCHARGEDCHARGE AIR COOLEDLIQUID COOLED DEISEL ENGING- DISPLACEMENT: 275 CU. IN. (4.5 LITRES)- GOVERNOR: ELECTRONIC.- LUBRICATION: FORCES CIRCULATION- AIR CLEANER: DRY TYPE- OIL RESERVOIR: 17.5 US QTS DRY / 15.5 US QTS REFILL- FUEL TANK: 88 GALLONS- FULL LOAD OPERATING RUN TIME: 21.7 HRS.- STARTER: 12VELECTRONIC- STANDARD FEATURES: ENGINE ENCLOSURE. LOW OIL PRESSURE ANDCOOLANT TEMPERATURE- SAFTETY SHUT DOWN SWITHCHES/INDICATORS. AUTOSTART INSTRUMENT.- OVERLOAD PROTECTION- MUFFLER AND WEATHER CAP- PUSH BOTTOM THROTTLE CONTROL.- WHEEL KIT- BALL STYLE COUPLER