Description

2013 Grove RT9130E-2, 130 tons, 160' main, 59' jib, 2 winches, Cummins, 40,000 lbs counterweight self removable, 80 ton block, 12 ball, well maintained and work ready!!

Description

2008 Terex RT230-1XL, 100' main, 43' jib, Cummins tier 3 with 2,690 hours, just repainted, looks and runs good!!

Description

2000 Broderson IC200-2C, 15-ton carry deck crane, 36' main, 15' jib, Cummins diesel, block & ball

Description

Manitowoc Encore - Crane Care Financing available!! RT 58B Model Re-Manufacture Manitowoc CraneCARE scope of work for the remanufacturing of RT 58B serial number 49409. Our Encore Certified Crane Check program was created to assist in laying down the parameters for a complete machine remanufacture and thorough inspection using OEM replacement parts and utilizing a factory owned and operated facility manned by specially qualified technicians. The scope of the program is to restore the unit as close to original specifications as possible. The machine will be completely disassembled, some components will be remanufactured, and many will be replaced with new parts. By major components:Engine was rebuilt by OEM (Detroit) back to factory specs. 2. All hydraulic hoses, tubing, gaskets, were replaced. 3. Hydraulic control valves, electric solenoids valves, flow dividers, holding valves and pilot operated check valves: were replaced/rebuilt with new components. 4. Hydraulic Cylinders: Steering, axle lock-out, outrigger extension, boom lift, boom telescopic, were remanufactured and pressure tested. 5. Hydraulic swivel was remanufactured, and pressure tested. The electric swivel was replaced. 6. Hydraulic and Fuel tanks were drained, removed, and thoroughly cleaned. New filters were provided including fuel and hydraulic and fuel-water separator. New fuel lines were installed. 7. All electric wiring harnesses were all replaced. 8. The batteries were replaced, and the alternator was remanufactured. 9. Lights and indicators: including headlights, back-ups, turn signals etc. were replaced. 10. Engine radiator was cleaned and inspected by local radiator shop. 11. All hydraulic pumps (steer, 3 stage, charge) were replaced. 12. Swing bearing, bolts, and all mounting hardware were replaced. 13. Model 15 main hoist was remanufactured. The wire rope, wedge, brakes, gear reduction units, cable follower bearings, sprag clutch, seals, etc. were replaced. A load test was performed. 14. Telescopic hydraulic boom assembly: The entire boom was removed and disassembled. Each section was inspected using our procedures to check for camber, twist, squareness, convex, concave or any structural defects. All hardware, sheaves, rope retainer pins, bearings, spacers, wear pads, extension and retraction cables inside the boom was replaced. 15. The four tires were replaced. Wheels were blasted and painted. 16. Drivelines and universal joints were replaced/rebuilt with new hardware. 17. New brake master cylinder, booster, brake lines and wheel cylinders were replaced. 18. The entire exhaust system was replaced. The air filter, canister and intake flex lines were replaced. 19. Remanufacturing of the cab will include the following:Replacement of all cab weather-stripping, cab acoustic, and floor mat.Replacement operators door latch, locks, and handles.Replacement of all cab glass and rubber seal.Replacement of all gauges, indicator lights, panels or control labels and switches.Replacemen

Description

Manitowoc Encore - Crane Care Financing available!!RT 58D Model Re-ManufactureManitowoc Crane Care scope of work for the remanufacturing of RT 58D serial number 79112.Our Encore Certified Crane Check program was created to assist in laying down the parameters for acomplete machine remanufacture and thorough inspection using OEM replacement parts and utilizing a factoryowned and operated facility manned by specially qualified technicians. Not all components were fully replacedon this machine, but all were tested, and all will hold an Encore Certified one-year warranty.By major components:1. Engine was rebuilt by OEM (Cummins 5.9) back to factory specs.a. Holds a one-year warranty through Cummins.2. All hydraulic fittings, valves, and hoses for the outrigger system were replaced.3. Hydraulic control valves, electric solenoids valves, flow dividers, holding valves: were tested andreplaced/rebuilt as needed.4. Hydraulic Cylinders: Outrigger, boom lift, boom telescopic, were remanufactured and pressure tested.5. Hydraulic swivel was pressure tested.6. Hydraulic and Fuel tanks were drained, removed, and thoroughly cleaned. New filters were providedincluding fuel, hydraulic, and fuel-water separator.7. The starter and alternator were remanufactured.8. Lights and indicators: including headlights, back-ups, turn signals etc. were replaced.9. Engine radiator was replaced with new.10. Hydraulic pumps (steer, three stage, charge) were tested.11. The wire rope was replaced. A load test was performed.12. Telescopic (60ft) hydraulic boom assembly: The entire boom was removed and disassembled. Each sectionwas inspected using our procedures to check for camber, twist, squareness, convex, concave or any structuraldefects. Hardware, rope retainer pins, bearings, spacers, wear pads, extension and retraction cables inside theboom was replaced.13. The four tires were replaced. Wheels were blasted and painted.14. Remanufacturing of the cab will include the following: Replacement of all cab weather-stripping, cab acoustic, and floor mat. Replacement operators door latch, locks, and handles. Replacement of all cab glass and rubber seal. Replacement of all gauges, indicator lights, panels or control labels and switches. Replacement of operators seat to include retractable seat belt. Replacement of steering wheel, steering column including horn switch. Replacement of side mounted mirrors, cab fan, dome light, wiper system, and accelerator pedal.15. Swing gearbox was tested16. The four outrigger beams were removed, blasted, and painted.17. Hook block structure and sheaves were inspected and replaced as needed.18. Headache ball was replaced with new.19. LMI - Wika QScale LMI (Load Moment Indicator) system retrofit with currently available technology willbe provided. This system shall provide comparable performance to existing new crane systems.20. Jib (20ft.) was blast and painted - after inspection. New locking pins, and cable was installed.21. Clean and paint the entire ma

Description

2008 TADANO GR600XL-1, 60 TON ROUGH TERRAIN CRANE, 7,500 HOURS, 36.4'-137.8' 5 SECTION BOOM, 32.5'-58.1' SWING AWAY OFFSET BIFOLD JIB, MITSUBISHI TIER 3 ENGINE, 5 SHEAVE BLOCK AND BALL, ANTI TWO-BLOCK, LMI, AUX WINCH, 29.5X25 TIRES, A/C 2 cranes available

Description

2008 GROVE RT700E 60 TON ROUGHT TERRAIN CRANE,7950 HOURS, 36'-110' 4 SECTION BOOM, 33'-56' BI-FOLD LATTICE SWINGAWAY OFFSET JIB, ANTI-TWO BLOCK, CUMMINS 6.7 TIER 3 ENGINE, PAT LMI, MAIN & AUX WINCH, HOOK BALL, JOHNSON 5 SHEAVE BLOCK, 29.5X25 TIRES, ON OUR YARD iN HOUSTON, TX, CRANE WILL BE FULLY SERVICED AND 3RD PARTY OSHA CERTIFIED IN YOUR COMPANY'S NAME BEFORE DEPARTURE

Description

Work done by Mustang Cat 9-1-21:DESCRIPTION PARTS LABOR MISC EXTENDEDMachine Already Washed- No Wash FeeRemove and Install Tracks $ 656.00 $ 656.00Swap Track Pads Onto New System 1 Links $9,230.02 $1,148.00 $10,378.02Reseal Track Adjusters $ 428.65 $1,312.00 $1,740.65Optional- Replace Sprockets $ 965.50 $ 656.00 $1,621.50Customer Discount -$1,376.00 -$1,376.00Main Shop to Troubleshoot Hydraulic CoolerLeak$ 648.00 $ 648.00Replace Radiator With New $3,917.92 $ 984.00 $4,901.92Lower Seat Suspension Replacement $1,817.27 $ 326.00 $2,143.27Remove and Install Bypassing Cylinder $ 326.00 $ 326.00Reseal Cylinder $ 386.99 $ 882.00 $1,268.99SUBTOTALS: $16,746.35 $6,938.00 -$1,376.00 $22,308.35*SUPPLY CHARGE IS 2% OF INVOICE TOTAL - MAXIMUM CHARGE OF $100.00 SUPPLY CHARGE: $ 100.00*ENVIRONMENTAL FEE IS 3% OF INVOICE TOTAL - MAXIMUM CHARGE OF $120.00 ENVIRONMENTAL FEE: $ 120.00SALES TAX: $ .00**Subject to additional parts/labor upon disassembly TOTAL: $22,528.35

Description

2011 National NBT45, 45 tons, 103' 4 section full power boom, 3 sheave main boom nose, Graphic LMI with audio-visual Warning System, signal horn and engine start/stop switch, hyd. oil cooler reservoir, crane cab A/C and heater, with defroster, 360 degree continuous rotation, main hoist with grooved drum, 450' of 5/8" 35x7 wire rope, "quick reeve" block with swivel hook, hydraulic front and rear out riggers, 52" steel torsion resistant sub-frame, steel crane cab mounted on a 2012 Peterbilt 367 Chasis, ISM425V diesel engine, Fuller RTO16908LL 10 speed trans., GCW: 80,0000lbs

Description

Located in Wisconsin. 196.9 Ft Boom, 55.8 Ft Jib / Two Additional 29.9 Lattice Inserts, Mercedes Engines, Two Winches, LMI, A2B, 86,000 Lb Counterweight, 700 Kg 3-Sheave Block, Extra 5-Sheave Sister Hook Block, 8 Ton Ball, Air Conditioning Up & Down, 3 axle dolly, 7,350 upper hours, 5,570 lower with 73,300 miles. Very clean and very well maintained. Work ready. Located in Wisconsin, USA

Description

2006 MANITOWOC 8500 S/N: 8501024, 85 TON LATTICE BOOM CRAWLER CRANE, 100 FT BOOM, Mitsubishi TIER 3 DIESEL ENGINE, LIVE GANTRY, RETRACTABLE CRAWLERS, HOOKBLOCK, HEADACHE BALL, SELF ERECTING COUNTERWEIGHTS, AIR CONDITIONER/HEATER, LOAD MOVEMENT INDICATOR, MAIN AND AUXILIARY DRUMS, 6,469 HOURS, GREAT CONDITION! , 1 OWNER CRANE, EXWORKS: HOUSTON, TXCURRENTLY INSTALLING NEW CABLE ON BOTH DRUMS and NEW PAINT, THE PICTURES ARE FROM THE SISTER CRANE WE JUST SOLD AFTER WE WERE FINISHED GOING THROUGH IT.

Description

154' Main Boom - 33--58' side stow jib - Two Winches - Full LMI with Anti-Two Block - 29.5 x 25 Tires - 4WD and steer - A/C & Heater - Auxiliary Lifting Sheave - Hook Block and Ball, Multiple Units available

Description

2009 JLG 600S, sold in good working condition

Description

8.5-ton carry deck crane, 30' main, 10' jib, Cummins diesel, 2,573 hrs

Description

8.5 ton carry deck crane, 20' + 10' jib, Cummins diesel, 3,690 hrs

Description

75 US ton capacity, 36.1 - 141.1 five-section boom, 33.1 - 58.1 bi-fold lattice jib, Auxiliary lifting sheave, Main & Auxiliary Hoists, Drum rotator indicator, Boom angle indicator, Hot water cab heater & A/C,4 x 4 x 4 drive/steer, 6.2 ton headache ball, 75 ton 7-sheave hook block

Description

Diesel engine.

Description

2011 GROVE RT880E , 80 TON ROUGH TERRAIN CRANE, 5,400 HOURS, 128' OF MAIN BOOM, 33'-56', SWING AWAY BIFOLD OFFSET JIB, 5 SHEAVE HOOK BLOCK, 12 TON HOOK BALL, HIRSCHMANN LMI, MAIN AND AUX WINCH, COUNTERWEIGHT REMOVAL DEVICE, A/C, 29.5X25 TIRES, SITTING ON OUY YARD IN HOUSTON, CRANE WILL BE FULLY SERVICED AND A 3RD PARTY OSHA INSPECTION IS INCLUDED IN THE PRICE AND WILL BE PUT IN YOUR COMPANY NAME.

Description

Foam filled tires and well maintained.

Description

2012 Terex CD225, 25 ton rough terrain, 72' main, 43' jib, block and ball, new decals have been ordered and crane will look even better, super clean, Lift cylinder rod replaced and resealed, all boom was removed and everything inside inspected including wear pads replaced that are hard to get to, chains greased, cylinders checked and boom replaced, new wire rope, new computer, completly serviced and ready to work!!

Description

Boom: 39.4-154.2 feet, 5 section boom and 33.2 / 58.1 feet bi-fold swingaway jib. Hoist: 2.. Drive: 4x4x4. Tires: 29.5x25. Engine: Cummins. 8 sheave, 100 ton (90.7 metric ton) with swivel hook and safety latch for(19mm) wire rope, 7.3 ton (6.6 metric ton) hook ball with swivel; Self-removable counterweight, Telematics (machine data logging and monitoring system) with HELLO-NET via internet

Description

One 1980 Grove model TM-1400, 140-ton hydraulic truck crane serial number 47913, equipped with 172 main boom, 88 luffing jib, two winches, Caterpillar diesel engines in upper and lower,12 x 6 carrier with 14:00 x 20 tires, hook block and swivel weight ball. Front hydraulic outrigger and counterweight extension. The crane swings, telescopes hoists. The carrier transmission andengine are good, It is an operational crane. It does not have either a Load Moment Indicator or anti-two block system. The exterior of the crane and the interior of the cabs are in poor condition.Note: The upper engine has less than 500 hours since being rebuilt. Lower shows 7708 miles, upper shows 3402 hours. Price: $99,000 fob, Hallsville, Texas

Description

1995 Galion 150FA SN 10565, Cummins engine 5,505 on old hour meter new meter with 3 hours, 60' main, jib, block and ball, just repainted, all oils and filters replaced, every single cylinder on the crane was repacked even the two boom extend cylinders, machine is work ready.

Description

80 ton capacity rough terrain crane, Cummins QSB6.7L (Tier 4) turbo-charged six cylinder diesel, 41 to 128 4 section full-power synchronized Megaform boom, 33 to 56 manual offsettable bi-fold boom extension, LMI with anti-two block system, Grove Model HP30-19G main hoist, Grove Model HP30-19G auxiliary hoist, 29.5x25 tires, enclosed cab with heater, a/c, overhaul ball, hookblock,